| Javascript Feeds RSS Feed Security Dashboard | SearchSecurity.com |
|
Configuring Clustering in NGAI Describes how to configure cluster state synchronization in Checkpoint NGAIr55.
Karim Ismail and Myles Buckley,
06/16/2004
|
|
Check Point NG FP3 step-by-step Install Guide on Nokia IPSO After using this document as a reference guide (not a configuration guide), you should be able to put the device in line and connect it to a management server with out any issues. This document guides you from entering in the hostname of the firewall, and ends with applying the default filter and running CPCONFIG. Good luck with your install and thanks for using this guide as a reference on how to configure a Check Point firewall.
By Brandon Robrahn, 05/23/2004
|
|
Solaris 8 and Checkpoint NG FP3 install with SSH, JASS and Syslog After determining the initial state of insecurity in an existing corporate firewall, the following discusses the process of building a hardened Solaris 8 Sun clone with SSH connectivity for remote firewall console access with Checkpoint NG FP1 firewall, an upgrade to FP3 then HF2, hardened further with JASS, and the last step remote syslog. Discussed below is the detailed account of the pre-existing insecurity, a brief note of the catalytic event precipitating the actual changes to the firewall, a discussion of the implementation, and the results and ultimate success of the procedure "hardening" the corporate firewall.
By Mike Shannon, 04/05/2004
|
|
Implementing NAT on Checkpoint Firewall-1 Network Address Translation, or NAT as commonly referred to, was initially designed as a temporary fix, before IPv6, to allow additional workstations to access routable networks across the Internet, without utilizing a routable, or valid IP address. NAT is simply defined as connecting multiple computers to the Internet, using one IP address. Today, a multitude of proxies, firewalls, VPN devices, routers and SOHO devices now use NAT to allow internal hosts to the Internet. This document will examine how NAT is implemented, specifically on Checkpoint Firewall-1 4.1 for Windows NT 4.0.
By Unknown, 04/05/2004
|
|
CheckPoint Secure Platform (SPLAT) With SecurePlatform, in less than 5 minutes a security administrator can turn an off-the-shelf Intel or AMD-based server into a high-performance VPN-1/FireWall-1 gateway.
By Unknown, 03/02/2004
|
|
Understanding the FireWall-1 State Table The intent of this paper is to help you understand how Firewall-1's stateful inspection works. This table is how FW-1 maintains who is doing what and what connections are allowed based on the rule base. To help you better understand your own FW-1 stateful inspection table and validate my data, I have posted all the source code I used at the bottom of this page.
By Lance Spitzner, 02/21/2004
|
|
SofaWare security policy management from Check Point SmartCenter SofaWare devices have factory pre-defined security policies. There is possibility to define user-defined security policy as described below.
By Mariusz Stawowski, 02/21/2004
|
|
Security policy, active protection against network attacks and management of IDP Intrusion Detection and Prevention (IDP ?) is a new generation of network security systems which implementation is NetScreen? IDP (formerly OneSecure?). This is a network security system performing intrusion detection tasks able to block attacks in a real time.
By Unknown, 02/21/2004
|
|
Resolving problems with SMTP Security Server and CVP operating in Check Point NG The Check Point FireWall-1 Next Generation (NG) security system provides powerful capabilities in terms of detailed and restrictive electronic mail control. It is performed by means of a dedicated security component — SMTP Security Server.
By Mariusz Stawowski, 02/21/2004
|
|
Nokia IPSO Password Recovery This is one bit of reference material that's surprisingly hard to come by but absolutely crucial to any Nokia shop.
Mitchell Rowton,
02/21/2004
|
|
Page: 1 23 |
